Map Dictionary:
CMD0 - Specifies input and output locations for the command interface

   e.g. CMD0=ESI25*ESO20
   Unit will look for commands starting at Ethernet/IP input word 25 and send acknowlegement to output word 20
   Please distinguish between digit zero "0", and upper-case letter "O".

DFI - DeviceNet Input, regarded as floats
DFO - DeviceNet Output, regarded as floats
DSI - DeviceNet Input, regarded as 16 bit integers
DSO - DeviceNet Output, regarded as 16 bit integers
DII,DIO - DeviceNet Input,Output, regarded as 32 bit integers
DI,DO - DeviceNet boolean input and output
EFI,EFO,ESI,ESO,EII,EIO,EI,EO - Ethernet I/P, similar to DeviceNet
PFI,PFO,PSI,PSO,PII,PIO,PI,PO - Profibus
RFI,RFO,RSI,RSO,RII,RIO,RI,RO - RIO. Words 0-63 for block transfer, Words 64-71 for discrete transfer
MFI,MFO,MSI,MSO,MII,MIO,MI,MO - Modbus-TCP
UFI,UFO,USI,USO,UII,UIO,UI,UO - Modbus-RTU
CFI,CFO,CSI,CSO,CII,CIO,CI,CO - ControlNet - Note: first 2 words of ControlNet output are not available
HSI - Hardy Short Input Table. This table allows the things in HI to be mapped as 16-bit words.

• HSI0 - Digital Input
• HSI0 bit 0 (HI0.0) - Digital Card Input 1
• HSI0 bit 1 (HI0.1) - Digital Card Input 2
• HSI0 bit 2 (HI0.2) - Digital Card Input 3
• HSI0 bit 4 (HI0.4) - User Switch 1
• HSI0 bit 5 (HI0.5) - User Switch 2
• HSI0 bit 6 (HI0.6) - User Switch 3
• HSI1 - Status Word
• HSI1 bit 0 (HI1.0) - A/D Conversion Error
• HIS1 bit 1 (HI1.1) - A/D Failure
• HIS1 bit 2 (HI1.2) - Center of Zero
• HIS1 bit 3 (HI1.3) - Weight Overrange
• HIS1 bit 5 (HI1.5) - Real Time Clock failure
• HIS1 bit 6 (HI1.6) - Motion
• HIS1 bit 8 (HI1.8) - SD memory card read failure
• HIS1 bit 9 (HI1.9) - Display error
• HIS1 bit 11 (HI1.11) - SD memory card write failure
• HSI2,HSI3,HSI4,HSI5 - Setpoints 1,2,3,4 Output
• HSI10,HSI11,HSI12,HSI13,HSI14 - Calibration year,month, day, hour, minute
• HSI15 - Calibration type. 0=C2 Cal, 1=Trad Cal
• HSI16 - Check Weigh Status Word
  • HSI16 bit 0 (HI16.0) - Check weight FAIL Low
  • HSI16 bit 1 (HI16.1) - Check weigh PASS
  • HSI16 bit 2 (HI16.2) - Check weight FAIL High
  • HSI16 bits 4,5,6,7 - check weight low, rising, high, falling
  • HSI16 bits 8,9,10 - Check weight quality - 000 = none, 001 = bad, 010 = low, 011 = med low, 100 = med high, 101 = high, 110 = excellent
  • HSI16 bit 11 (HI16.11) - Check low weight more than 2 motion_thd intervals away from check zero weight for 32 or more of the last 128 cycles.
  • HSI16 bit 12 (HI16.12) - Check low weight measurement in progress.
  • HIS16 bit 13 (HI16.13) - Check weigh - stable weight on scale
  • HIS16 bit 14 (HI16.14) - Check weigh - stable weight off scale
• HSI17 - Check Weigh Status Word 2
  • HSI17 bit 0 (HI17.0) - set if the Check Weight is between check_lo_lo and check_lo
  • HSI17 bit 1 (HI17.1) - set if the Check Weight is between check_hi and check_hi_hi
  • HSI17 bit 2 (HI17.2) - Photo Eye 1 state
  • HSI17 bit 3 (HI17.3) - Photo Eye 2 state
  • HSI17 bit 4 (HI17.4) - external trigger 1 is detected
  • HSI17 bit 5 (HI17.5) - check delay time reached
  • HSI17 bit 6 (HI17.6) - check_time has been reached
  • HSI17 bit 7 (HI17.7) - stable check wieght value calculated
  • HSI17 bit 8 (HI17.8) - Off Check error
  • HSI17 bit 9 (HI17.9) - On Check error
  • HSI17 bit 10 (HI17.10) - check alarm

HSO - Hardy Short Output table. This table allows the things in HO to be mapped as 16-bit words.

• HSO0 - Digital Output
  • HSO0 bit 0 (HO0.0) - Digital Card Output 1
  • HSO0 bit 1 (HO0.1) - Digital Card Output 2
  • HSO0 bit 2 (HO0.2) - Digital Card Output 3
  • HSO0 bit 3 (HO0.3) - Digital Card Output 4

• HSO1 - Command Status - value returned after a command (see HSO2) is done. Non-zero status means the command failed
• Status 1,2,0x40 = Calibration, Zero, or Tare failed due to ADC error, ADC failure, or Motion
• Status -8 (0xFFF8) = Hard Calibration failed, not enough ADC counts between high and low steps
• Status -6 (0xFFFA) = C2 Calibration failed, no C2 sensors detected
• Status -10 (0xFFF6) = C2 Calibration failed, bad C2 sensors detected
• HSO2 - Command Word. Commands are performed on a 1-shot basis when this word changes from 0 to 1. An error code is returned in the "command status" word HSO1.
  • HSO2 bit 0 (HO2.0) - Tare
  • HSO2 bit 1 (HO2.1) - Zero
  • HSO2 bit 2 (HO2.2) - Hard Cal Low
  • HSO2 bit 3 (HO2.3) - Hard Cal High
  • HSO2 bit 4 (HO2.4) - C2 Cal
  • HSO2 bit 5 (HO2.5) - Write Parameters to SD card
  • HSO2 bit 6 (HO2.6) - Print
  • HSO2 bit 7 (HO2.7) - Clear Tare
  • HSO2 bit 8 (HO2.8) - Midpoint Cal
  • HSO2 bit 9 (HO2.9) - Disable Midpoint Cal
  • HSO2 bit 10 (HO2.10) - Start Check Weigh Zero measurement
  • HSO2 bit 11 (HO2.11) - Clear Check Weigh Tamper
• HSO3...HSO5 - Unused

JSO Hardy Short Integer Parameters

• JSO0 -WAVERSAVER®
• JSO1 -Num Averages
• JSO2 -Unit
• JSO3 -Decimal Point
• JSO4 -AutoZero Enable
• JSO5 -Grad Size
• JSO6 -Setpoint 1 Mode
• JSO7 -Setpoint 1 Type
• JSO8 -Setpoint 2 Mode
• JSO9 -Setpoint 2 Type
• JSO10 -Setpoint 3 Mode
• JSO11 -Setpoint 3 Type
• JSO12 -Setpoint 4 Mode
• JSO13 -Setpoint 4 Type
• JSO14 -Param Value MSW
• JSO15 -Param ID MSW
• JSO16 -Check weigh Time constant
• JSO17 -Check weigh card sample rate
• JSO18 -Check weigh card filter
• JSO19 -Check low weight error count
• JSO20 -check mode
• JSO21 -Check Zero Mode

HFO Hardy Float Parameters

• HFO1..HFO7 - Scratchpad variables
• HFO8 - Tare Weight
• HFO9 - Motion Tolerance
• HFO10 - Zero Tolerance
• HFO11 - AutoZero Tolerance
• HFO12 - Span Weight
• HFO13 - Cal Low Weight
• HFO14 - Scale Capacity
• HFO15,16,17 - Setpoint 1 Target, Preact, Deadband
• HFO18,19,20 - Setpoint 2 Target, Preact, Deadband
• HFO21,22,23 - Setpoint 3 Target, Preact, Deadband
• HFO24,25,26 - Setpoint 4 Target, Preact, Deadband
• HFO27 - Custom Display(a number that will appear on the front panel display)
• HFO28-31 - Input to one of 4 channels of analog output card
• HFO32-35 - Analog output channel 1 configuration: WeightLow, WeightHigh, OutputVoltsLow, OutputVoltsHigh
• HFO36-39 - Analog output channel 2 configuration: WeightLow, WeightHigh, OutputMilliampsLow, OutputMilliampsHigh
• HFO40-43 - Analog output channel 3 configuration: WeightLow, WeightHigh, OutputVoltsLow, OutputVoltsHigh
• HFO44-47 - Analog output channel 4 configuration: WeightLow, WeightHigh, OutputMilliampsLow, OutputMilliampsHigh
• HFO48 - Check weigh variation_thd
• HFO49 - Check weigh motion_thd
• HFO51 - Check high_thd
• HFO52 - Check low_thd
• HFO53 - Valid check weight high
• HFO54 - Valid check weight low
• HFO55 - check_zero
• HFO56 - Midpoint cal test weight
• HFO57 - CheckOffset
• HFO58 - CheckLoLo
• HFO59 - CheckHiHi
• HFO60 - CheckOverRide
• HFO61 - CheckTime
• HFO62 - CheckDelay

HFI Hardy Float Parameters (read only)

• HFI0 - Gross weight
• HFI1 - Net Weight
• HFI2-5 - Analog Output setpoints, calculated from scaling HFO28-31
• HFI6 - Rate of Change (if enabled)
• HFI7 - ON Check Weight (if enabled)
• HFI8 - OFF Check Weight (if enabled)
• HFI9 - Check Weight ON-OFF (if enabled)

WII

• WII0 - A/D convertor raw counts
• WII1 - A/D convertor average counts